Microstructural and Tribological Behavior of Pulse Electroplated Nickel Barrier on Copper Conductors

The microstructural, mechanical, and tribological behaviors of electroplated Ni on Cu conducting substrates have been investigated in this study. The microstructural studies were performed by X-ray diffraction (XRD) analysis and scanning electron microscopy (SEM). The results showed that initially (111) with (220), (200) Ni texture components were predominant in the coating, and increasing the current density from 0.1 to 0.5 A/cm² led to the development of a strong (111) texture. The presence of ultrafine grains coupled with a (111) Ni texture improved the coating microhardness and wear properties significantly. It was shown that with an increase in current density, wear resistance of the coatings improved significantly and the electrical resistivity increased due to the highly populated grain boundaries.     

电磁搅拌对大圆坯结晶器冶金行为影响的探讨

 为了探究结晶器电磁搅拌(M EMS)对大圆坯结晶器内综合冶金行为的影响。以大断面圆坯连铸结晶器冶金行为为研究对象，基于电磁热流体与凝固传输理论建立三维耦合数值模型。揭示大圆坯连铸常用五孔水口浇注条件下结晶器内电磁场、流场、传热与凝固等综合冶金行为，提出电磁搅拌对结晶器冶金性能影响的多参量评价方法。以中碳铬钼齿轮钢650 mm大圆坯连铸为例，指出结晶器电磁搅拌存在最佳搅拌电流，可获得相对较好的综合冶金效果。具体表现为弯月面保持一定的切向速度和过热度，有利于保护渣的熔化和夹杂物的上浮去除；液面波动幅度在控制范围内，可避免卷渣、改善表面质量；结晶器内钢液过热得到有效耗散，有利于等轴晶形核改善铸坯内部质量；侧孔出流钢液速度得到有效控制，可抑制注流对初凝坯壳的冲刷，提高了初生坯壳生长的均匀性。此外，电磁搅拌产生的水平旋流强度也可得到有效控制，有利于避免常见的皮下白亮带现象。     

深圳抽水蓄能电站监控新技术应用研究与实践

通过对安防、工业电视和门禁等新技术的研究,设计了一套先进的监控系统,包括硬件平台、系统管理、应用软件,利用深圳抽水蓄能电站已形成的光纤网络通道把分布在方圆10 km范围内多个站端设备以环路的方式连接起来,把可靠成熟的新技术融合到整个平台。自首台机组成功投运,监控系统为电站正常运行保驾护航,高清摄像机、视觉识别、行为分析、边界防护等新技术的应用为工程项目增添了亮点,使电站现场管理更加智能化、规范化。     

基于人体关节点数据的攻击性行为识别

针对人体攻击性行为识别问题，提出一种基于人体关节点数据的攻击性行为识别方法。首先，利用OpenPose获得单帧图像中的人体关节点数据，并通过最近邻帧特征加权法和分段多项式回归完成由人体自遮挡和环境因素所导致缺失值的补全；然后，对每个人体定义动态"安全距离"阈值，如果两人真实距离小于阈值，则构建行为特征矢量，其中包括帧间人体重心位移、人体关节旋转角角速度和发生交互时的最小攻击距离等；最后，提出改进的LightGBM算法w-LightGBM，并对攻击性行为进行识别。采用公共数据集UT-interaction对所提出的攻击性行为分类识别方法进行测试实验，准确率达到95.45%。实验结果表明，所提方法能够有效识别各种角度的攻击性行为。     

Compressive strength and wear properties of SiC/Al6061 composites reinforced with high contents of SiC fabricated by pressure-assisted infiltration

Pressure-assisted infiltration was used to synthesize SiC/Al 6061 composites containing high weight percentages of SiC. A combination of PEG and glass water was used to fabricate SiC preforms and the effect of the presence of glass water on the microstructure and mechanical properties of the preforms was evaluated by performing compression tests on the preforms. Also, the compressive strength and the hardness of the SiC/Al composites were investigated. The results revealed that the glass water improved the compressive strength of the preforms by about five times. The microstructural characterization of the composites showed that the penetration of the aluminum melt into the preforms was completed and almost no porosity could be seen in the microstructures of the composites. Moreover, the composite containing 75 wt% SiC exhibited the highest compressive strength as well as the maximum hardness. The results of the wear tests showed that increasing the SiC content reduces the wear rate so that the Al-75 wt% SiC composite has a lower wear rate and a lower coefficient of friction than those of Al-67 wt% SiC composite. This indicated higher wear resistance in these composites than the Al alloy due to the formation of a tribological layer on the surface of the composites.     

Wear and thermal behavior of basalt fiber reinforced rice husk/polyvinyl chloride composites

Plant fiber reinforced polymer composites (PFRPs) in practical application are often subjected to both complex friction and variable temperature environments. The present work explores the possibility of reinforcing rice husk/polyvinyl chloride (RH/PVC) composites with basalt fibers (BF) for developing a new wear resistant material with improved thermal stability. The results showed that the structural strength and wear resistance of the composites increased at first and then decreased with an increasing ratio of BF/RH, the highest value occurred at a BF/RH ratio of 8/42. The thermal stability of composites had a positive relationship with BF/RH ratio. The composites added with BF all possessed improved performance in comparison with unadded composites. Hence, the findings of this article proposed some new perspectives on improving the wear resistance and thermal stability of PFRPs that would broaden their practical application.     

CrN和CrN/Ag涂层的真空高温摩擦磨损性能*

为改善涂层在真空、高温等苛刻条件下的摩擦学性能，利用中频直流磁控溅射技术在硅片和316L不锈钢上沉积了CrN和CrN/Ag涂层，利用扫描电镜、透射电镜和X射线衍射仪对涂层的成分及相结构进行了表征，通过划痕测试仪、纳米压痕仪和摩擦磨损试验机测试了涂层的力学及摩擦学性能。结果表明：添加Ag元素以后，CrN/Ag涂层硬度及承载能力有所减小，但结合强度增加；真空高温环境下CrN与CrN/Ag涂层摩擦因数随温度升高呈下降趋势，其中CrN涂层通过软化镀层减小剪切强度和阻力，从而减小摩擦因数，CrN/Ag涂层主要通过高温产生的热驱动力诱导表面Ag润滑膜的形成来减小摩擦因数；CrN涂层依靠自身剪切特性参与摩擦，而CrN/Ag涂层在真空高温下具有自润滑和持续润滑性能，作为自润滑零部件具有潜在的应用价值。     

Differences in indentation and wear behaviors between the two sides of thermally tempered soda lime silica glass

Thermal tempering is an industrial process widely used to make soda lime silica (SLS) glass panels stronger and tougher. During the tempering process, the upper and bottom sides of the glass may experience different cooling rates, and thus, their properties could be different. This study characterized changes in surface composition and subsurface glass network structures as well as indentation and wear resistance properties of the air- and tin-sides of 6-mm-thick SLS window panels faced toward the upper and sliding roller sides during thermal tempering. The results showed that although the chemical and structural differences detected with X-ray photoelectron spectroscopy and specular reflection infrared spectroscopy are subtle, there are large differences in nanoindentation behaviors and mechanochemical wear properties of the SLS glass surface. The findings of this study provide further insights into the performance difference between the air- and tin-sides of the SLS glass panel treated with thermal tempering.